dangerdave
Member Since: 23 Nov 2010
Location: Cheshire
Posts: 568
|
| Resetting Service Indicator |
|
Works on a 58 D3.
1.Insert the key
2.With off ignition press trip recorder reset button
3.Keep pressed trip recorder reset button and turn key so ignition light come on, but not start up, longer 2 seconds
4.There displays blinking message Service. After finishing of blinking release the button
5.There displays message DIST
6.A short press reset button will change messages DIST -> DATE -> END
7.Select DIST and hold the button longer 5 seconds there will display Reset and occur reset a
service distance
8.Select DATE and hold the button longer 5 seconds there will display Reset and occur reset a
service interval
9.Select END and hold the button longer 5 seconds there will finished the service mode
|
 Fri Dec 31 2010 6:14pm |
|
|
choppa60
Member Since: 16 Oct 2009
Location: chelsea tractor land ....london
Posts: 899
  
|
 when mine was due a service at 60,000 there was nothing on the dash to say service was due .08 hse 2008 ,hse, it does what it says .
|
| Sat Jan 01 2011 5:16pm |
|
|
dangerdave
Member Since: 23 Nov 2010
Location: Cheshire
Posts: 568
|
Strange, my service is due in a week, I got the usual dash reminder a couple of weeks before hand. just reset it. It also helps if you have had to disconnect the battery, that sends to trip the service due display.
|
| Sat Jan 01 2011 9:21pm |
|
|
Jean-Paul
Member Since: 07 Jun 2009
Location: Athens
Posts: 122
 
|
i cannot get this to work. i put the key in, push once the reset button, then leav it, and then push and hold it while turning the key so that light and system check is done. no blinking service indicator.
also tried inserting the key and pushing and holding the reset button while turning the key so that light and system check is done. again no blinking serv. indicator
what am i doing wrong ? J.p
|
| Sun Feb 20 2011 10:37am |
|
|
NickJ
Member Since: 11 Oct 2010
Location: left a bit
Posts: 933
|
Think I read that the reset procedure only works from a certaion MY date onwards, if like mine you have a 2005 than I think it's too early Without a shepherd, sheep are not a flock
|
| Sun Feb 20 2011 10:39am |
|
|
Jean-Paul
Member Since: 07 Jun 2009
Location: Athens
Posts: 122
|
yeap. mine is an early 2005. is there a soluion fr us or visit workshop ? J.p
|
| Sun Feb 20 2011 1:54pm |
|
|
chocolademan
Member Since: 02 Nov 2010
Location: Snowy Oslo (formerly West Yorks)
Posts: 822
 
|
Jean-Paul wrote:yeap. mine is an early 2005. is there a soluion fr us or visit workshop ?
Did you manage to reset it? I have a 06 and have same problem.
Can't reset it  Tailgate Actuator DIY: http://www.disco3.co.uk/gallery/albums/use...IY%7E0.pdf
Expo Rack, Faultmate FCR, FBH adaptor, GVIF, Blackvue,
FBH Timer, Webasto Diagnostic Tool, Built in Charger, Headlight mod,
Megaflush.
|
| Wed May 04 2011 4:16pm |
|
|
|
|
Jean-Paul
Member Since: 07 Jun 2009
Location: Athens
Posts: 122
|
nopel.so solutions for us. only workshop J.p
|
| Wed May 04 2011 5:12pm |
|
|
BBS SPY
Site Sponsor
Member Since: 15 Jun 2007
Location: Cyprus where it is still surprisingly warm.
Posts: 1593
|
To clarify:
Somewhere between 2006 and 2007 Land Rover started fitting instrument Packs that had the ability, through the sequence dangerdave, the OP notes, to self reset the Service interval reminder / Announcer (SIA) according to built in re set values.
However this simply does not work on earlier vehicles, typically fitted with earlier instrument packs, unless after the change, they had their instrument packs replaced with a later spec one for some reason.
Therefore someone with an 05 or 06 vehicle might report it working but it's really quite rare.
Earlier vehicle owners therefore used to have no other choice but to have their vehicles serviced and have their reminders reset at a main dealers, again only as per pre set values.
But as crwoody states, there is now another option in the form of the BBS Canmate SRT.
Of course it can do the same as main dealers can but also offers a lot more besides.
See this thread, and my post on it to get more information about its capabilities.
http://www.disco3.co.uk/forum/topic64611.html?
|
| Wed May 04 2011 6:58pm |
|
|
Splitpin
Member Since: 30 Dec 2010
Location: Worcester
Posts: 297
|
I have a scanner that can reset the indicator if required for anyone in the Worcester area in exchange for a nice cup of tea!
|
| Wed May 04 2011 7:21pm |
|
|
Ollram
Member Since: 04 Dec 2006
Location: Gortynia
Posts: 375
|
dealer for me 
|
| Thu May 05 2011 6:04pm |
|
|
Matty 2332
Member Since: 02 Dec 2008
Location: West Yorkshire
Posts: 379
|
Mines an MY05 so the DIY did not work. Now the proud owner of one of BBS's Canmate, great piece of kit 
|
| Thu May 05 2011 7:57pm |
|
|
billy56
Member Since: 23 May 2008
Location: co antrim
Posts: 58
 
|
Mine is an 07 model and tried this, but no joy so BBS tool bring ordered soon!!
|
| Thu May 05 2011 7:58pm |
|
|
billy56
Member Since: 23 May 2008
Location: co antrim
Posts: 58
|
Now ordered
|
| Thu May 05 2011 9:47pm |
|
|
